Invite a Co-worker
Send a co-worker an invite to the Exchange portal.Just enter their email address and we’ll connect them to register. After joining, they will belong to the same company.
Send Invite Cancel
80737members
346702posts

QR450 Trio Radio

Solved
DarrenBravo
Crewman
Crewman

QR450 Trio Radio

Hi community- Does anyone have any info on how to set up QR450 radios – 1 x Gen 2 & 1 x Gen 1. in Qam mode with IP routing. I have upgraded both to the latest firmware – 2.5.0.7859
 
For now im just trying to get coms working- one radio connect to my PC, other over-air.
 
Any help would be highly appreciated.
 
Thank you

Accepted Solutions
Joel_Weder
Commander Commander
Commander
0 Likes
0
263

Re: QR450 Trio Radio

The videos are indeed an excellent resource. A couple of other resources:

 

1) The Wizards in the radio's Setup pages. At the top of the list of configuration pages you'll see Wizards. Click on that, then at the bottom of the page you'll see a Point to Multipoint via Multiple Repeaters wizard. That one pre-configures many parameters of typical radios in an IP Routing system. You may want to make changes afterwards but it gives you a really good head start.

 

2) The Trio Q radio user manual has plenty of good information on  configuring a system for IP Routing. If you don't have it, you can get it by installing the TView Management Suite software package. That software also includes a very good diagnostic software tool, at no charge. Once the software is installed you just go to Start > Trio Datacom and scroll down to the Q manual.

 

To acquire TView, go to se.com, click on the Products menu, then select Telemetry & Remote SCADA Systems in the lower-right of the list. On that page, scroll down and select the Licensed radios, then you'll find TView in the Software and Firmware tab.

 

Also note that the current released version of firmware for the Q radios is on the same page. It's at version 2.5.2 right now. You may want to consider upgrading your radios to the latest version.

 

Joel Weder
Remote Operations Specialist
Schneider Electric

See Answer In Context

2 Replies 2
MartinChartrand
Commander Commander
Commander
0 Likes
0
268

Re: QR450 Trio Radio

Hi DarrenBravo,

A good place to start is the YouTube playlist for Trio radio "How to" videos: <click here for playlist> 

 

Regards,

Martin

 

 

Joel_Weder
Commander Commander
Commander
0 Likes
0
264

Re: QR450 Trio Radio

The videos are indeed an excellent resource. A couple of other resources:

 

1) The Wizards in the radio's Setup pages. At the top of the list of configuration pages you'll see Wizards. Click on that, then at the bottom of the page you'll see a Point to Multipoint via Multiple Repeaters wizard. That one pre-configures many parameters of typical radios in an IP Routing system. You may want to make changes afterwards but it gives you a really good head start.

 

2) The Trio Q radio user manual has plenty of good information on  configuring a system for IP Routing. If you don't have it, you can get it by installing the TView Management Suite software package. That software also includes a very good diagnostic software tool, at no charge. Once the software is installed you just go to Start > Trio Datacom and scroll down to the Q manual.

 

To acquire TView, go to se.com, click on the Products menu, then select Telemetry & Remote SCADA Systems in the lower-right of the list. On that page, scroll down and select the Licensed radios, then you'll find TView in the Software and Firmware tab.

 

Also note that the current released version of firmware for the Q radios is on the same page. It's at version 2.5.2 right now. You may want to consider upgrading your radios to the latest version.

 

Joel Weder
Remote Operations Specialist
Schneider Electric