EcoStruxure IT forum
Schneider Electric support forum about installation and configuration for DCIM including EcoStruxure IT Expert, IT Advisor, Data Center Expert, and NetBotz
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-03 12:14 PM
This question was originally posted on DCIM Support by Ed Tarento on 2017-01-29
A DCO 8 system has several network devices (showing an "N" in a yellow box next to the Genomes and the modeled device) that have been configured with blade slots. However, I can't find a way to add a blade to these devices. I've checked blade size and orientation and ensured the Family name is an exact match. But I cannot get a blade in these chassis.
Is it correct that "Network Type" devices ("N" n a yellow box) cannot accept blades, even though it is possible to configure them with slots?
I.e. if I need to put blades into the slots of these devices, I have to remodel the Genomes devices as "Blade Chassis" showing "B" in a grey box, delete and recreate the assets?.
(CID:110791340)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-03 12:14 PM
This answer was originally posted on DCIM Support by Jef Faridi on 2017-01-30
Hi Ed,
Currently in DCO it is supported to add "switch modules" into "switch enclosure", it might fail if there should be mismatch between the module and enclosure. If needed you might want to try customizing/adding "Generic Switch Module" to your network chassis:
Kind regards
(CID:110791617)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-03 12:14 PM
This comment was originally posted on DCIM Support by Ditte Drewer Mathiasen on 2017-01-30
Hi Ed Tarento, thanks for posting. Lets see who can be of assistance here. @community any ideas?
Kind regards Ditte
(CID:110791548)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-03 12:14 PM
This answer was originally posted on DCIM Support by Jef Faridi on 2017-01-30
Hi Ed,
Currently in DCO it is supported to add "switch modules" into "switch enclosure", it might fail if there should be mismatch between the module and enclosure. If needed you might want to try customizing/adding "Generic Switch Module" to your network chassis:
Kind regards
(CID:110791617)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-03 12:14 PM
This comment was originally posted on DCIM Support by Ed Tarento on 2017-02-01
Thanks Jef, right you are
(CID:110792231)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-03 12:14 PM
This comment was originally posted on DCIM Support by Jef Faridi on 2017-02-01
You are most welcome, Ed
Kind regards
(CID:110792258)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-03 12:14 PM . Last Modified: 2023-10-22 04:25 AM
This question is closed for comments. You're welcome to start a new topic if you have further comments on this issue.
Link copied. Please paste this link to share this article on your social media post.
Create your free account or log in to subscribe to the forum - and gain access to more than 10,000+ support articles along with insights from experts and peers.