EcoStruxure IT forum
Schneider Electric support forum about installation and configuration for DCIM including EcoStruxure IT Expert, IT Advisor, Data Center Expert, and NetBotz
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-04 08:46 PM
This question was originally posted on DCIM Support by jared reed on 2018-07-25
(CID:132668707)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-04 08:47 PM
This answer was originally posted on DCIM Support by Justine Chester on 2018-07-25
Hi Jared,
The setting that I have mentioned will show the current date and time of the DCE server as shown in the image below:
However, if what you are looking for is an area on the DCE client that will show the set time (in real-time) I believe this is not available.
Regards,
Justine
(CID:132668737)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-04 08:46 PM
This answer was originally posted on DCIM Support by Justine Chester on 2018-07-25
Hi Jared,
The time settings of the DCE appliance can be seen under System->Server Administration Settings->Time Settings from the DCE software client.
This is also where you can set the DCE as an NTP Server, change regional settings, time settings, and more importantly set the DCE appliance's date and time.
I hope this answers your question.
Cheers!
Kind regards,
Justine
(CID:132668711)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-04 08:47 PM
This comment was originally posted on DCIM Support by jared reed on 2018-07-25
Sorry but I cannot see the current time here.
ie. the hour:minute:seconds ticking over.
(CID:132668719)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-04 08:47 PM
This answer was originally posted on DCIM Support by Justine Chester on 2018-07-25
Hi Jared,
The setting that I have mentioned will show the current date and time of the DCE server as shown in the image below:
However, if what you are looking for is an area on the DCE client that will show the set time (in real-time) I believe this is not available.
Regards,
Justine
(CID:132668737)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-04 08:47 PM
This comment was originally posted on DCIM Support by jared reed on 2018-07-25
Hi Justine,
Yes, looking for the set time in real time.
Thanks for your help.
Jared
(CID:132668749)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-04 08:47 PM
This comment was originally posted on DCIM Support by Justine Chester on 2018-07-25
You are welcome
(CID:132668759)
Link copied. Please paste this link to share this article on your social media post.
Link copied. Please paste this link to share this article on your social media post.
Posted: 2020-07-04 08:47 PM . Last Modified: 2023-10-22 02:38 AM
This question is closed for comments. You're welcome to start a new topic if you have further comments on this issue.
Link copied. Please paste this link to share this article on your social media post.
Create your free account or log in to subscribe to the forum - and gain access to more than 10,000+ support articles along with insights from experts and peers.