Issue Unable to monitor a SmartStruxe Lite MPM controller over a Building Management System using BACnet to an AX BMS Product Line EcoStruxure Building Expert Environment SSL MPM Cause Misconfiguration of BACnet settings on a MPM controller. Resolution Open Building Expert on the controller with a supported browser. In this example both the MPM controller and the BMS system are in the same IP subnet range. Highlight the Device's name e.g. SmartStruxure Controller and go to the Configuration tab. On Ethernet Settings (ETH1) The IP address of the MPM controller must be in the same subnet IP range of the BMS IP address, but not the same IP address. Netmask must be the same subnet on both controllers (MPM and BMS) e.g. 255.255.255.0, if not then a BBMD/Foreign Device needs to be used. Gateway IP if used. On BACnet Settings (BAC1) Network ID (171) used on the MPM controller must be different than the BMS network numbers used for BACnet MS/TP and BACnet IP Set Protocol to BACnet IP Click on the upper-left icon (Save database to flash) Important! Right-click on "SmartStruxure Controller" then on "Restart Controller," be patient. On the BMS Jace AX, under BACnet network, click on Discover, uncheck all MPM Networks assigned within the MPM (if this facility is available in the BMS), in this example we have only one, it’s #171, refer to point 4. If you don't uncheck MPM network number, the devices will still discover but with duplicates. In this example, network #1 is the BMS IP network and needs to be checked. Network #300 is the BMS MS/TP network number, and has no impact on discovering the MPM as a BACnet device. Click OK. Here’s the result of the discovery, all the objects we had at point 4. are shown. Now add the Devices to the Database, then select one device (in this example the SE8600 is selected), click the Discover button, all objects we had in point 4. are now in AX. Add them to AX database.

Issue Create EWS between SmartStruxure and SmartStruxure Lite Product Line EcoStruxure Building Expert, EcoStruxure Building Operation Environment StruxureWare Building Operation site SmartStruxure Lite site Cause Steps to create EWS (EcoStruxure Web Service) between SmartStruxure and SmartStruxure Lite Resolution Release requirements: SmartStruxure Building Operation Release 1.3.938 and higher SmartStruxure Lite Version: Schneider Electric 2.7.0 and above Verification the Enterprise Server is running Open Building Operation Software Administrator. If Status shows Stopped, you must configure Building Operation. Otherwise, proceed to step 2. Ensure all Ports are correctly configured. Click Start Service and wait until application running shows in Path field. Click OK. Building Operation is now ready to integrate with SmartStruxure Lite The following example is using Server 1 in System Tree tab. In System Tree tab, right-click on Server 1. In newly opened window, select New. In newly opened sub window, select Interface. Click on Web Service to expand. Select EcoStruxure Web Service. In Name field, enter EcoStruxure Web Service. Click Next button. In Server field, enter IP address of Multi-purpose Manager (MPM) Controller you are connecting with. In Protocol field, ensure Communication port matches that on your server. In SOAP Endpoint field, enter ews in lower case letters. Take note that from SBO version 1.5 onwards, 'SOAP Endpoint' has been renamed to 'EWS Path'. IMPORTANT: You must enter ews in lower case letters in step 11. NOTE: If you are connecting to another StruxureWare Server, you must use an account that is in the default domain for log in credentials. Click Create button. Allow database to save completely before moving on to next step. In Server Tree tab, ensure new interface shows. You are now ready to connect your MPM Controller with Building Operation. Refer below to “Procedure - Connect MPM Controller to Building Operation." Procedure - Connect MPM Controller to Building Operation Ensure your MPM is physically connected to your workstation. In Server Tree tab, expand System folder. Expand Hardware folder. Expand EcoStruxure Web Services folder. Right-click C2G_root folder and select Host EWS Objects in sub window. Expand EcoStruxure Web Services folder. Select EcoStruxure and then select Web Services Properties Tab. Set Alarm Polling to Disabled. Procedure - View and Watch Data Points Expand CAN2GO controller. The List View tab shows all Objects available in Device. NOTE: EWS Consume in Building Operation server does not support connection over a ProxyServer.

Issue Unable to determine whether the Enocean device in hand is compatible with MPM controllers Unable to add more devices to a MPM controller Product Line EcoStruxure Building Expert Environment Multi-Purpose Manager Cause Some pre-configured icons in the "Add Devices" list have a name but do not have a specified Enocean profile or vice versa. Resolution The Following devices are embedded in the MPM firmware and require no scripts to integrate with an MPM. All Devices in the below list (except for Enocean relay) are outbound devices (i.e. devices that are only able to send telegrams to other devices) MPM Sub-device list Description Compatible Schneider-Electric Products CO2 Sensor A5-09-04 CO2 Sensor SR04 CO2 (LSS442510) (868MHz) Door/Window Sensor D5-00-01 Single Input Contact SED-WDS-U-5045 (902MHz) 10020032 (LSS10020032) 10020042 (LSS10020042) 10020047 (LSS10020047) Double Rocker Switch F6-02-01 Light and Blind Control – Application Style 1 EDRPU-W-EO (902MHz) 10020048 (LSS10020048) (868MHz) Enocean Relay Inbound profile   Enocean Switch Light and Blind Control – Application Style 2 ESRPU-W-EO (902MHz) 10020049 (LSS10020049) (868MHz) Enocean Thermostat Obsolete   KeyCard Switch F6-04-01 Key Card Activated Switch SED-KCS-U-5045 (902MHz) Light Sensor A5-06-01 Light Sensor Range 300lx to 60.000lx 10020047 (LSS10020052) Light Sensor A5-06-02 Light Sensor Range 0lx to 1.020lx SED-LLS-U-5045 (902MHz) LSS10020053 (868MHz) Motion Sensor A5-07-01 Occupancy Sensor with Supply Voltage monitor SR-MDS Bat SED_CMS_U_5045 (902MHz) Thermostat A5-02-05 Temperature sensor Range 0°C to +40°C SED-T00-U-5045 (902MHz) 10020046 (LSS10020046) 10020033 (LSS10020033) Thermostat A5-04-01 Temperature & Humidity sensor Range 0°C to +40°C and 0% to 100% SED-TH0-U-5045 (902MHz) 10020041 (LSS10020041) SR04 rH Thermostat A5-08-01 Light, Temperature and Occupancy sensor Range 0lx to 510lx, 0°C to +51°C and Occupancy Button SR-MDS Thermostat A5-10-03 Room Operating Panel: Temperature Sensor and Set Point Control SR04 P (LSS226172) Thermostat A5-10-05 Room Operating Panel: Temperature Sensor, Set Point and Occupancy Control SED-TS0-U-5045 (902MHz) Thermostat A5-10-10 Room Operating Panel: Temperature and Humidity Sensor, Set Point and Occupancy Control SED-THS-U-5045 (902MHz) Thermostat A5-10-12 Room Operating Panel: Temperature and Humidity Sensor and Set Point SR04P rH(LSS252331) Thermostat A5-10-19 Room Operating Panel: Humidity, Temperature Set Point, Temperature Sensor, Fan Speed and Occupancy Control   -The maximum number of devices added to each MPM is 49 -The maximum number of EnOcean devices added to each MPM is 49 -The maximum number of EnOcean devices with the same EEP added to each MPM is 49 .This only applies to firmware 2.13.1 and later, the limit for previous firmwares is 20. An Exception is the following limits for devices/widgets per MPM 20 EnOcean Switches 20 EnOcean Relays 4 EnOcean Thermostats The Devices in the next table do not have a pre-configured icon in the devices list, however, scripts can be used instead and can be found below (Please read PDF first) Enocean Scanner Enocean device driver Valve driver Enocean profiles supported in script EnOcean Equipment Profile (EEP) Description Example of Compatible Devices (EEP A5-38-08) Central Command Gateway Plug-in 15 Amp 120V 902Mhz 5-Wire 6A Relay 24V 902Mhz 3-Wire 6A Relay 120/240/277V 902Mhz (EEP A5-11-01) Lighting Controller 15A-20A 120/277/347V 902Mhz (inbound profile: A5-11-01) 15A 120-277V 902Mhz (inbound profile: A5-11-01) (EEP A5-10-04) Temperature Sensor, Set Point and Fan Speed Control Thermokon SR04PS (EEP A5-02-14) Temperature Sensor Range -20°C to +60°C Thermokon SR65TF (EEP F6-03-01) 2 to 4 Rocker Switch (Light and Blind Control) Push-button, 2-gang (EEP A5-20-1) Battery Powered Actuator Thermokon SAB02/SAB05     Din Relay 1 channel (inbound profile: F6-02-02)     PWM 230V valve driver (inbound profile: A5-02-05) PWM 24V valve driver (inbound profile: A5-02-05)

Issue Current information will be stored and updated in release notes and online documentation. Compatibility Matrix of Operating Systems, Video, Product Announcements, SQL Compatibility Product Line Andover Continuum, EcoStruxure Building Expert, EcoStruxure Building Operation, Satchwell Sigma, TAC IA Series, TAC INET, TAC Vista Environment Windows Operating Systems and iBMS (intelligent Building Management System) Software Cause Compatibility, Firmware, Product Announcements Resolution Please see release documentation for current and recent products. For the Firmware compatibility matrix for: I/NET, it is available HERE or the EcoBuilding Download Center Continuum, click HERE Xenta Software Downloads HERE Vista, click HERE StruxureWare Building Operation, click HERE Product Announcements can be a great tool for discovering which products have been tested and are compatible with the different versions. These documents are available on the Extranet, but have been compiled here for ease of access: I/NET 2.40   Product Announcement 2.41   Product Announcement 2.41a Product Announcement 2.42   Product Announcement and Compatibility Matrix (page 5) 2.43   Product Announcement PA-00239 2.44a Software Available from Exchange Download Center 2.45   Software Available from Exchange Download Center 2.46 Software Available from Exchange Download Center 2.47 Software Available from Exchange Download Center 2.47a Software Available from Exchange Download Center 2.47b Software Available from Exchange Download Center 2.48 Software Available from Exchange Download Center Operating Systems and SQL Supported Video Compatibility Support Policy PA-00279 Software Support for TAC I/NET Continuum v1.92 Product Announcement v1.93 Product Announcement v1.94 Product Announcement PA-00210 1.94 SP1 Product Announcement PA-00273 1.9 - 2.1 Software, Firmware, & Video  Compatibility Matrix Concerning IE10 and IE11 browser support  2.0 Feature Blast 2.0 + 2.01/ 2.02 Update Compatibility Matrix 2.0  Product Announcement PA-00353 2.0 CyberStation Installation Guide 2.0 WebClient Installation Guide 2.0 Software License and Ordering Activation Process 2.0 Software and Controller Upgrade Process Andover Continuum PA-00333 Support Policy PA-00272 for Andover Continuum Vista v5.1.5 Product Announcement v5.1.6 Technical Product Advisory v5.1.7 release note document, TAC Vista Compatibility Matrix, SNVT Matrix documents, and TPA-VSTA-11-0020.00 v5.1.7 Product Announcement x5.1.8 Release Note TAC Vista 5.1.8 and TAC Xenta 500/700/900 5.1.8 v5.1.9 Vista Compatibility Matrix SecurityIAS Product Announcement PA-00291 Product Announcement TAC Vista transition to SmartStruxure solution overview  Support Policy PA-00274 for TAC Vista Satchwell Sigma v4.05 SEB Release Notes v4.06 Release Notes v4.06 Release Note Supplement v4.07 Release Notes Satchwell Sigma Standard Edition Installation and User’s Guide Support Policy PA-00297 for Satchwell Sigma v4.08 Release Notes PA-00397 Sigma Version 4.08 Sigma server on a virtual machine Satchwell Micronet data sheet - MicroNet View 2.1 OS Compatibility - Micronet View PA-00228 Product Announcement Support Policy PA-00298 for Satchwell MicroNet PA-00228 Satchwell MicroNet End of Commercialization Announcement I/A Series PA-00163 I/A Series R2 & G3 Product Announcement PA-00114 Legacy Products Windows 7 Compatibility I/A Series R2 with Windows Compatibility Chart PA-00243 Software Product Update - Q2 2013 PA-00251 Hardware Product Update - Q2 2013 PA-00278 Software Product Update - Q3 2013 I/A Series (Niagara) R2 Windows Compatibility Matrix with additional detail I/A Series (Niagara) AX/G3/N4 Windows Compatibility Matrix with additional detail Support Policy PA-00280 R1 for TAC I/A Series StruxureWare Building Operation Please visit Maximum number using StruxureWare Building Operation (Scalability and Capacity) SmartStruxure Lite Please visit SmartStruxure Lite solutions

Issue Continuum 1.9x and above will not install correctly on a PC / Laptop that is on a domain, One example: When trying to run the Continuum Database Initialization program the following error message may pop up: You must have local NT administrative privileges to run this application. Environment Windows OS 7 8 10 Continuum 1.9x 2.x Inet SQL 2005 SQL 2008 SQL 2012 Cause Microsoft has introduced the use of a higher level of security in the install of their SQL database software SQL 2005 / SQL 2008 / SQL 2012. When you install Continuum you need to make sure you are logged onto the PC / Laptop as a local administrator, in the case of a lot of a corporate networks, you are most likely logged on as ether a restricted user or a domain administrator, these logons do not have the privileges you need to install an SQL database. Resolution Step by step guide to creating a local administrator user on your PC / Laptop Go to "Start" then "Control Panel" in Windows (Windows 7 and above, top right corner change "view by" to "small icons" this will show all icons) Go to "Administrative Tools" Go to "Computer Management" / "Local Users and Groups" In users, right click on the right panel and add new user Fill in the user name and password, un-tick user must change password Tick password never expires then ok it Now go back into control panel and click on "User Accounts" Click on the name you just created, this will open the properties screen (Windows 7 and above click on "Manage user accounts") Click on "Group Membership" then select others, and highlight administrators (Windows 7 and above double click on name you created, click "group membership" click "other" then in the drop down select "Administrator") Apply this and then ok it. Log off your normal account and log back on as the new user you have just created

Issue What specification should the Continuum BACnet MS/TP cable meet? Product Line Andover Continuum, EcoStruxure Building Expert, EcoStruxure Building Operation Environment Systems using BACnet MS/TP comm's, with b3 controllers and 3rd party MS/TP devices. MSTP Cable type Spec Cause Often an incorrect cable type is used when wiring MS/TP devices, unless the correct cable specification is used it is unlikely you will get reliable communications. Resolution The BACnet Controller Technical Reference defines the following cable specification for a MS/TP (MSTP) cable: RS-485 Cable Specifications: Cables used to form the RS-485 network should conform to the following specifications: Wire Size: 22-24 AWG Cable Type: Twisted-pair, copper wire, tinned Shield: Braid Nominal Impedance: 100-120 Ohms Velocity of propagation: 78% Capacitance: <12.5 pF/ft (~ 41pF/M) between conductors and < 22 pF/ft (~72pF/M) between the conductor connected to ground and the next conductor. An example of a cable that meets this specification is Belden 3105A. Also check out the SmartStruxure-RS485-Network Installation Quick-Help video on the Exchange.

Issue General use of the Wireshark program. Product Line Access Expert, Andover Continuum, EcoStruxure Building Expert, EcoStruxure Building Operation, Pelco, Satchwell MicroNet, Satchwell Sigma, TAC IA Series, TAC INET, TAC Vista Environment Ethernet Networks Cause General Information on using WireShark. Resolution Wireshark is an Ethernet packet analysis programme, Which can be downloaded from: Latest version available from Wireshark Locally stored version 1.0.9 Installing Wireshark If necessary, unzip the WireShark executable file to a suitable location on the PC/Laptop you wish the programme to be installed on. Run the executable file and follow the on-screen instructions. Rules for capturing LAN traffic using Wireshark: Do not use a switch or router to connect the LAN capture PC to the network as these will filter important network activity that you will need to see. You will want to capture everything that is passing over the network at the point of concern. Usually, this means tapping into the ethernet at the Controller or controllers, that is having an issue. midBit-Technologies-LLC-10-100 is an example of a device that can be used to easily tap into the network to take the capture. The monitoring PC must see all traffic from the controller's point of view. The monitoring PC can be connected in either two ways: Connected to the network at the controller The customers IT department can mirror all the network traffic from the controllers port to another port the PC can be connected to. If connected to the network at the controllers, the connection must be made through a true ethernet hub. A hub will not selectively filter important network traffic as a switch or a router will do. More information on what a "true ethernet hub" can be found at http://wiki.wireshark.org/HubReference There are however some switches that feature port mirroring, please see How to Configure a NETGEAR Prosafe Plus Switch for Mirroring. If connected to a mirrored port, the port must mirror 100% of the network traffic to and from the controller. No filtering should be done. Once a complete capture file has been obtained it can be filtered after the fact using WireShark or EtherReal. Using Wireshark Run WireShark Start a trace by choosing the "Capture" menu and then select "Interfaces" Choose the appropriate interface. Generally, this can be identified by its IP Address, but if not, then the packets increasing are an indication. Press the "Start" button. The trace will start and will be similar to the following screenshot. After an appropriate time, the trace can be stopped by selecting "Capture" menu and "Stop" To save the capture file, choose "File" menu and "Save As".

Warning Potential for Data Loss: The steps detailed in the resolution of this article may result in a loss of critical data if not performed properly. Before beginning these steps, make sure all important data is backed up in the event of data loss. If you are unsure or unfamiliar with any complex steps detailed in this article, please contact Product Support Services for assistance. Issue Software installation problems with Windows 7 OS and above Configuration problems also known as UAC / User Account Control These problems occur when you receive an error message stating that you do not have the correct administrative rights to continue. Product Line Andover Continuum, EcoStruxure Building Expert, EcoStruxure Building Operation, Satchwell MicroNet, Satchwell Sigma, TAC INET, TAC Vista Environment Windows 7 Windows 8 8.1 Windows 10 Server 2012 Cause Windows 7 and above user administrator privilege settings (UAC) Resolution The solution to this issue is to turn off the user admin settings before the software is installed by following these instructions: Go to Start > Control Panel. Set the view to "small icons" to show all Control Panel icons Click on "User Accounts." Make sure that the account used for installing the software is a full admin user. On this page, click on "Change User Account Control settings", a slider bar that starts with "Never notify" up to "Always notify" by default will be set to "Notify me only when programs try to make changes to my computer" Set it to "Never notify." This will disable all the admin blocks that pop up in installing and configuring software Once set, restart the PC and then continue with your software installation and configuration Once all is installed and working, the feature may be turned back on if required. Additional requirements for Windows server 2012 and Windows 10. Please note: this process may open the "Windows 10 Firewall up" For Windows Server 2012 and Windows 10, additional steps are required to disable User Account Control. Although the slider bar can be set to “Never Notify”, the User Account Control does not disable completely. The User Account Control can be disabled for any user by setting the system registry value “EnableLUA” to zero in the system registry under the registry key “HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\policies\system”. A Windows registration file has been included in the Continuum 2.01 release in order to expedite these additional steps. Or the attached file EnableLUA.zip can be used, unzip and execute.  Supplement: Using the right click "run as administrator" instead of this is not the same. The right click will only run that .exe as an administrator and not the whole install/configuration package, i.e. SQL2005 manager will fail to run if you do not do as instructed above. You will always get an error stating that you do not have permission to run this program.  Alternate Windows 10 Admin. to User privilege for I/Net Seven:   Go to this path: C:\Program Files (x86)\ Inet Seven 1) Rename and move to a new folder these files.       A) INetIoSrv.exe.manifest       B) INetW.exe.manifest       C) If there is a file equalization client, then there is INetEqzMerge.exe.manifest to do this change on as well.  2) Change the DbCreate by doing this:       Another problem for non-admin users will be logging into and using DbCreate. A work-around for that would be to create a new login into the SQL database that could be shared among all DbCreate users and would provide the necessary rights.       Alternate Windows 7 Admin to User privilege for I/Net Seven:  See the attached Document and Manifest Files  

Issue XIF and Device Resource files for the Schneider Electric SE7000 Series Room Controllers Product Line EcoStruxure Building Expert, Field Devices, TAC IA Series Environment SE7000 Series Room Controller Cause In order to commission Schneider Electric SE7000 Series Room Controllers into an LNS system, the XIF is required. Resolution LonWorks External Interface Files (XIF) SE72_73_PIR.XIF (80:00:10:55:00:04:04:20) SE76_PIR.XIF (80:00:10:55:00:04:04:21) SE76RH_PIR.XIF (80:00:10:55:00:04:04:22) Device Resource File for XIFs listed above. For Datasheets for the SE7000 Series Controllers, see Where to find datasheets and information on the SE7000/SE8000 series room controllers.

Issue Are there I/A Series R2 and G3 objects for interface with the SE7000 Series Room Controllers? Environment I/A Series R2 and G3, SE7000 Series Room Controller Cause Not able to locate shadow objects with matching LonWorks program IDs within the existing I/A Series R2 and G3 modules. Resolution A set of new modules have been generated for use with the new SE7000 Series Room Controllers.  The new objects interface with the following program IDs. R2 objects: Se7273         (80:00:10:55:00:04:04:20) Se76Pir         (80:00:10:55:00:04:04:21) Se76RhPir    (80:00:10:55:00:04:04:22) Click to download ... lonSchneider-2.301.330.zip Click to download ... lonSchneider-2.301.431.zip Click to download ... lonSchneider-2.301.534.zip G3 objects: Se72_73.lnml (80:00:10:55:00:04:04:20) Se76Pir.lnml (80:00:10:55:00:04:04:21) Se76RhPir.lnml (80:00:10:55:00:04:04:22) Click to download ... lonSchneider-3.5.39.1.zip Click to download ... lonSchneider-3.7.17.zip The 3.5.39.1 module should be used with G3 versions 3.5 and lower. The 3.7.17 module should be used with G3 versions 3.6 and higher.

Issue When defining configuration on SE7300 part no, your choice is between "0" (override) and "5" (possibility to change between °C and °F in interface). Environment SE7300 Cause its not possible to have both override and °C/°F feature Resolution When defining the part number, you will have to choose. The override feature is usually the preferred choice in industrial applications, while the °C/°F feature is used for Hotels and similar, where users are given the possibility to change unit of desired temperature.

Issue When specifying the configuration of the SE7300 you can choose between "50" and "55" in step 5 of the part number. Product Line EcoStruxure Building Expert, Field Devices Environment SE7300 Cause Different options of configuration when defining the part no for the SE7300 Resolution The difference is that the "50" option is PIR Ready, but PIR cover of unit is not included. Option "55" is with the PIR cover already mounted upon delivery. 

Issue What options of running wireless communication is available for the SE7000 series controllers? Environment Viconics SE 7000 series controllers Cause Wireless communication options on SE7000 series controllers. Resolution There are 2 communication options for wireless: BACnet IP or BACnet MSTP . At this time there is no option for LON wireless.

Issue Want to be able to run the SE7200 in floor heating and chilled beam simultaneously. Environment SE7200 Cause running simultaneous applications. Resolution Unfortunately the SE7200 will only handle 1 main application per controller due to its limited I/O.

Issue The difference between VWG-APP-1045 and   VWG-EPP-1045 option cards. Environment I/A Tridium SE7000 VWG-EPP-1045 VWG-APP-1045 Cause Different cards available. Resolution VWG-APP-1045:   option card  that fits directly into a Tridium JACE controller to provide communications between controllers and the gateway device. VWG-EPP-1045: option card that fits directly into the American IA range of controllers with an RS232 interface

Issue How to find the correct SE7000 series controller Environment SE7000 SE7200 SE7300 SE7600 Cause There are several different SE7000 series controllers to choose from and it is important to select the correct one for the application Resolution The online selection tool is available SE7000 Room Controller Selection

Issue Where can I find the SE7000 Room Controller LonMaker Plug-Ins and device resource files? Environment SE7000 Series Room Controller Cause Plug-ins and device resource files required for interface into LON network management tools (e.g. Echelon LonMaker, etc.). Resolution The files are available for download from the Exchange Extranet.

Issue Where are the product specifications and application details for the SE 7000 or SE 8000 range of room controllers? Environment SE7000 Series SE7000, SE7200, SE7300, SE7600, SE76x7 SE8000 Series SE8600, SER8300 Ex Viconics branding. Cause Full details of the products are required. Resolution The best source of information is in the online Product Selection: Room Controller Selector Tool This tool will allow you to select the correct unit for your application, then from the different tabs you will be able to see: Product Overview, Spec's, Dimensions, related accessories and to download the required documentation from the Links tab. Note: The installation guide can be downloaded from the Links tab and contains detailed application setup, product specification and dimensions. For BACnet versions of the controllers the PIC's statements can currently be downloaded from the Viconics section of the BTL official site using the corresponding VT7xxx part number, see link: BTL Listings for Room controllers Note: The SE8000 and SE8300 Series BTL Certification Listing is anticipated for late 2015.

Issue LonWorks Zone Controller SE7200F5545E Environment Site requiring information or literature regarding this zone controller Cause Cannot find information on: Part Number: SE7200F5545E Part Name: ZNCTRL LONWORKS 2X0-10V PIR Part Short Description: LonWorks Zone Controller :2 Analog 0-10V Outputs, PIR Cover Installed. Part Long Description: LonWorks Zone Controller:2 Analog 0-10V Outputs with PIR Cover Installed   Resolution Please find the following guides: SE7000 Series Room Controller Brochure SE7200 Series Room Controller Data Sheet SE7200 Room Controller with Integrated PIR Motion Sensor Data Sheet PIR Ready SE7200 Series Installation Guide SE7200 and SE7300 Series LonWorks Integration Manual

Issue Sometimes, switching 230V with the SE7000 controller is requested and/or necessary, but no such product is listed in the current portfolio. Environment SE7000 series controllers Cause No product that matches the requests are currently listed in the portfolio Resolution Two relay boards for fan coil units will be released late 2012.  These will allow the SE7000 devices to be used with 230V systems.